DISC Shure PSM200 Wireless In Ear Monitor System

Full Description

Hearing music through your earphones on-stage is far more reliable than using a wedge speaker, thanks to Shure's monitoring system. There can often be short delays in music coming out of the wedge, resulting in out-of-time playing and a sloppy performance. With in-ear personal monitoring, the sound is constant and comes with you wherever you go. Using Shure sound isolating earphones cuts out the sound around you, leaving you to focus on playing in time and giving the best performance you can deliver.

Simply connect two line-level or mic-level inputs directly into the transmixer, set the frequency using a single button and the same on the bodypack receiver. Connect you rearphones to the receiver, set up your desired mix using the personal controls and you're ready to go!

SE215 Sound Isolating Earphones

These earphones shield over 90% of the ambient noise, contain a Single Dynamic MicroDriver and include a Fit Kit for your comfort. The Kevlar® coated cable is sturdy, reliable and tangle-free.

P2R Wireless Bodypack Receiver

The P2R can operate as a wired or wireless bodypack, or both simultaenously. It has a built-in headphone limiter, integrated cable management and a high-impact plastic chassis. It also has a frequency locator and 1/4" Line input jack with high/low gain switch.

P2T Wireless Transmixer

The P2T only takes up 1/2 rack space and has handy LED indicators and a tri-colour input level. Two mic/line input channels allow mix control, with input level control too. The P2T also features a built-in audio limiter and front-mounted antenna.

Features and Specifications

• RF Output Power: 10 - 30 mW (countryspecific)
• Operating Distance: Up to 100 mm
• Harmonic distortion: 1.5 % typical
• Signal-to-noise-ratio: 80 dB (A) typical
• Listening mode: Mono
• Compatible Systems per band (up to): 4
• Transmitter Inputs: 2x XLR/6,3 mm combo, mic/line level
• Transmitter Outputs: 2x XLR split outputs
• Wired Bodypack Option: Yes
• Personal Mix Control: On transmitter
• Remoteable Transmitter: No
• Battery Life: Wired: 6 h; Wireless: 4 h
• Frequency Response: 30 Hz - 12 kHz

EP2T TransMixer

• Modulation Limiter: Internal peak limiter (>10:1 hard knee compression)
• Antenna: 1/4 Wavelength, semi-rigid, PCB Mount
• Connector Type: XLR/1/4-inch combo
• Nominal Input Level: 25 dBu @ 1/2 volume (12 o'clock)
• Maximum Input Level: 5 dBu @ 1/2 volume (12 o'clock)
• Current: 170 mA maximum
• Dimensions: 220 mm x 140 mm x 40 mm
• Net Weight: 370 g

P2R Receiver

• RF Sensitivity: 109 dBm typical
• Squelch Threshold: 102 dBm typical
• Antenna: Attached Whip
• Audio Input Connector: Connector Type: 1/4-inch Mono
• Impedance: 1 megohm
• Maximum Input Level: LO = +0 dBu; HI = 10 dBu
• Frequency Response: 30 Hz to 20 kHz (+/ 3 dB); earphone dependent
• Power Requirements: 9 V alkaline battery, Duracell type MN1604 recommended
• Audio Output Connector: 1/8 inch (3.5 mm)
• Minimum Load Impedance: 8 ohms
• Net Weight: 100g, less battery
• Overall Dimensions: 122 mm x 73 mm x 32 mm

SE215 Earphones

• Frequency Range: 22Hz ? 17.5kHz
• Sensitivity: 107 dB SPL/mW (@ 1kHz)
• Impedance: 20 Ohms (@ 1kHz)
• Input Connector: 3.5mm (1/8")
• Colour: Clear
• Cable Length: 162 cm (64")